Видео

thanks man God bless you

How do I get ahold of you to rebuild my m21

Fantastic build quality. All four of your videos are premier quality tutorials.. I hope to have YOU build my M20.. thanks again. Brian.

Paul I'd like to say thank you for this video. You helped me completely rebuild my super t10. I won't be able to test it for a while, but darn near everything in it is new now, and I did everything you did, even used anaerobic gasket maker.

N

Nobody in the other videos mentioned the the mass/inertia of the gears locking the ring until it slows down enough to "blip" backwards like you mentioned thank you sir i better understand now

Thanks!

Great video. It also shows how important having a bit of knowledge about the underlying mechanisms which you’re using to be able to actually do this job DIY. Your experience is obvious. But I appreciate your attention to detail and your explanation. I’m listening to a slight whine in my Dana44 now and I will be referring to this video when it’s time to rebuild. Thanks

where should i go to get a new transmission

Some hard earned lessons for advice there. Thank you.

Just curious, If you install a oil slinger before the fromt bearing, how does oil get to the bearing?

Thanks!

Great info. Any particular gear oil that you prefer? 80W-90 wt?

Found Mr Freddy on RUclips called him and setup a time to come down and meet. Just so happened he was going to the Turkey Rod Run in Daytona and I was also Met and purchased a Toploader setup kit for a 66 Mustang 6 Cyl to V8 swap Very knowledgeable and Assisted me (an old Chevy guy) to accomplish this job Very satisfied with the purchase and everything went well with the swap. Do yourself a favor and contact him and save yourself some heartache

I am using your excellent video to rebuild the t5 in my 83 cj7. I purchased a new 3rd gear for my year and model but the tooth count is 27 instead of 29 like my original. The outside diameter is .055" less than the original. Should I use this? When ordering, they don't tell you the tooth count. Can you advise me?

I just bought a Muncie 2 weeks ago off a friend for my 70’ Nova. When will your out of stock parts be back??

About to tackle one of these on a 67 mustang. Just a reseal tho. Look pretty easy. Thanks. 🤘🤘

thanks paul fascinating

Recently got my M21 reassembled, and boy what a fantastic help this video series and your 661 store have been. And i struggled a bit on things you made look easy, but it all did go very well. Had to replace more things than I'd planned on, even bought a small press to get the job done. One thing I ended up doing that made a difference, when dropping my main shaft in I kept having issues getting the keys in the hub to line up with the slots in the ring. I just couldn't see any of it once they got close. I ended up using a sharpie to make marks on the hub where the keys were, and on the brass ring where I could still see them once the shafts got close. Worked like a charm. Should be back in the car this week. Thanks again Paul :)

Hey Paul, love the videos. What am I missing? Every time I snug that center bolt on my GTO M20, the shifter becomes so snug. It’s hard to go be between all the gears. I have to loosen it up a little bit so I can shift smoothly, but eventually the bolt works its way out even with the lock washer and the flat washer? Am I missing a part? Or should I just snug it and use thread locker?

Thank you Paul, for the beautiful m-22 box you built for me 4 years ago!! coupled with my 4;11 rear in my 71 nova, and my Mr Gasket v- gate, my youth has returned!! thanks again, shes flawless!

Try to fix my spdo gear on the main shaft it looks plastic and is way to far forward can I replace it without disabiliing the whole transmission

2 years ago i lost my gear box Audi 2.0 ,6 speed after fill the gear box with GL-5. That GL-5 destroyed all syncronized rings. Many auto parts sellers dont care about GL-3 OR GL-4 OR GL-5 but this is very important .

Great explanations mate! Cheers from Australia.

Hello thank you for your awesome videos! I have a question regarding gearbox oil and transmission fluids. Are they the same and can be used interchangeably for manual and automotive cars. My company is currently facing a dilemma if we should write transmission oil or gearbox oil. thank you very much.

Always a joy to watch you make a decent gearbox a perfect gearbox. Thanks for your tenacity to detail !

Does the top loader have different lengths of input shafts?

lots of great information thank you

I'm finishing up this project now. My biggest "lesson learned" is to buy retaining ring pliers, not snap ring pliers. I about broke my thumb nail off when using a big set of snap ring pliars. I found a cheap set of retaining ring pliers at advanced auto, Napa had a set too but harbor freight doesn't carry them at this time. Also, organizing the old snap rings to size the new ones up would have saved me considerable time.

Impressive description

Very informative. What disappoints me is why Hurst doesn’t address the weaknesses in their product.

hey paul i have a richmond 5 speed along with scnyros i have bad vibration 2nd and third gear 2nd gear at 4k bad vib 3rd gear some vib 4 th gear less 5th gear 0 does this sound like a bent shaft to u thanks matt

Congrats on 100k! Been watching you for years and love the content. Wish you’d make more!

The question arose where I could buy 2 gears, since mine was blown up

excellent video and explanation of the basics in a manual clutch system. well done Paul

I changed my bearing retainer I really appreciate your tips made it very easy for me I did need the thicker gasket thank you so much

Hi Paul I change that I use tremec t5 I have doubts if it is word class e or STD. Identification Box 13-52-065-922 identification label: (aluminum label screwed to the box) J3091 4408-3 204530 3205003

Would have a Dana 300 Shift Rail Seal Retainer for sale ?

Was looking for shifters you sell. Can’t find them in the online store.

First off, amazing channel im glad i found it and you now have a new subscriber. My question is i have an 87 Thunderbird turbocoupe with the wc t5. Under high rpm and boost it grinds bad going from 2-3 enough to where i have to double clutch to avoid it. Im assumint synchro is shot? And or fork. I've rebuilt 3 speed autos years ago but have never torn into a manual. I am going to be doing it myself with your videos to guide me along. Does my symptom sound like its caused by what parts i mentioned? It does not grind at all under normal to medium acceleration. Thanks!

BTW, love your videos!

so the locking or non-interlocking syncroteeth (brass syncro) take ALL the engine horsepower torque through those beefy gears? I thought the syncro teeth were there just to match up with the adjoining gear so that the sliding shift gear can ingage the wide span of the gear itself

Great vid!! Thank u!! Jus bought a 82 cj5, the forks r stuck, i took drain plate off and there was barely enough oil to lube teeth on gears, plus i found half of a very thin round metal shim or bearing seal. Cant find the other half, but, gears and everything looks great, despite the item. Magnetic drain plug had just a little bit of metal, minor, thoughts?

Thank you

Hi I have a 1985 C4 with this Transmission. My question is to do with a comment you made in this video around the 6 minute mark I think the problem is to do with the bearing pushing the seal out of the housing causing the trans stuck in reverse gear (I haven't been able to get the car out of reverse the last time I had the car out for a drive) Do I have to drop the overdrive unit to get the shifter to get into neutral?. or do I need to drop the whole transmission to get the overdrive out for repair. Thank you and look forward to your reply. Cheers

Great video and great product! I have had on in my t5 for the last 4 years now!

How can i buy one of your rebuild kits and your book?

Hi Paul, I'm here in Jupiter. I called you a couple of weeks ago about parts for a Tremec 3550. You referred me to a company and I got the parts. Thanks to this video I have the transmission rebuilt except for sealing it up. And of course I cleaned the case, all the parts and the debris magnet throughly! Do you still recommend anaerobic sealant for assembly? And, what transmission fluid do you recommend currently? Is Dexron VI ok???

hello awesome video! I have a situation and i need advice. I bought a 2015 mitsubishi mirage g4 manual and i had a mechanic do the transmission oil change and he said that the cars here in Panama use 80w90 but the manufacturer recommendation is 75w80, i found 75w80 but wasnt easy and had him change the gear oil but now the car is acting up, vibrated a lot on first gear going up a ramp at the mall hardly could make it up. was it the change from the thicker gear oil to the thinner oil that caused it?